Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
This post following next pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is particularly stimulating. Don't bypass it.
Installing a bathtub isn't specifically brain surgery, but it does call for strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately challenging task. If the old tub is conveniently easily accessible, the project can move speedily; if you need to open a wall to remove the old tub and place the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. Ensure you have certified on your own for the task and are comfortable trying it. Rather than hiring a contractor to take control of a halfway-completed job, it is better to consider employing one before you start. Possibilities are you may need a professional plumber to make tube connections.
This write-up will help you install a new bath tub in your bathroom if you have already acquired a new bathtub and don't require to transform the plan of your previous water system pipes.
Your devices and product list should consist of the following:
Preparing for the Setup
Firstly, the supporting framework provided with the bath must be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets system to stop strain on the bathtub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing taps can be rather troublesome because of the limited gain access to that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will come from the pipes. When the supply pipes have actually been gotten rid of, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the needed setting. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by examining the level and readjusting the feet on the bathtub till the level reviews level.
To mount faucets, fit the bottom of the outermost flexible faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
Switch on the water supply and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill the bath tub and additionally inspect the overflow outlet and also the normal outlet for leaks.
Ultimately, repair the bath paneling as defined in the supplier's user's manual. Tiling and also securing around the bathtub should wait up until the bathtub has actually been utilized at least once as this will certainly resolve it right into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washers are in place between the faucet and the sink. Safeguard the faucet in position with the maker provided backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The previous type should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall between the bathroom as well as the tiling, causing difficulties with wetness and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealant can break relatively very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently readily available on the market. It is advisable to fit the tiles utilizing water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up on How to Install a Bathtub through someone on another web blog. Remember to take the time to share this blog if you liked it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Dial, we're waiting! Report this page